Common misunderstandings of automotive lubricants

Automotive lubricants are used at a very high frequency during maintenance. In addition to protecting the engine and reducing the number of oil changes, high-quality lubricants can also save on gasoline expenses. At the same time should also pay attention to not cause improper use of lubricants caused by improper use of the car, "improper" use of the method is generally derived from the four types of lubricants on the "misunderstanding."

Misconception 1: Lubricants can be added more

The amount of lubricant should be controlled between the upper and lower tick marks of the oil dipstick. Because too much lubricating oil will enter the combustion chamber from the gap between the cylinder and the piston to form a coke combustion. These coke deposits will increase the engine compression ratio and increase the tendency to produce knocking. Coking in a red hot state in the cylinder will also cause premature combustion. If it falls into the cylinder, it will increase the wear of the cylinder and the piston, and it will also accelerate the pollution of the lubricant. Secondly, too much lubricating oil increases the stirring resistance of the crankshaft connecting rod, which increases the fuel consumption.

Misunderstanding 2: When the lubricant becomes dark, it is time to change the oil.

This understanding is not comprehensive. For lubricating oils that do not add a clear dispersant, the color blackening is indeed a sign that the oil has been seriously deteriorated, but the lubricants used in Hyundai Motors are generally added with a decomposing agent. This clearing agent cleans the film and black coke adhering to the piston and disperses it in the oil to reduce the formation of high-temperature deposits in the engine. Therefore, after the oil is used for a period of time, the color tends to turn black, but this time The oil has not completely deteriorated.

Misunderstanding 3: Lubricants often add no change

Regular inspection of lubricants is correct, but supplementation without replacement can only compensate for the lack of oil, but it cannot fully compensate for the loss of lubricant performance. During the use of lubricating oil, the quality of the lubricating oil will gradually decrease due to pollution, oxidation, etc. At the same time, there will be some consumption and the quantity will decrease.

Misunderstanding 4: Large use of additives

A truly high-quality lubricant is a finished product with a variety of engine protection functions. Formulations already contain a variety of additives, including anti-wear agents, and lubricants are the most balanced formulas to ensure full performance of all kinds of performance. Adding other additives on their own will not only bring additional protection to the vehicle, but will also react with the chemical substances in the engine oil, resulting in a decline in the overall performance of the engine oil.

  Architectural Hardware Precision Casting or architectural hardware investment casting, silica sol process. It is a casting process with little or no cutting. 

Cast architectural hardware is an excellent process technology in the foundry industry. Its application is very extensive. Architectural hardware cast not only applies to the casting of various types and alloys, but also produces the dimensional accuracy of castings. The surface quality is higher than that of other casting methods, and even castings that are difficult to cast and which are difficult to cast have high temperature resistance and are not easily processed can be cast using investment casting.

 In wax pattern process,we mix stearic acid and paraffin wax in wax pattern making,as you know,it is better than polyethylene,and the wax deformation is small.   

 In shell making,we adopt automatic sand-covering production line, which was invented under the guidance of our general manager.The indoor temperature was controlled by air-conditions,keeping the temperature at  24℃±1℃, which can make the castings much more stable,the internal tissues much more well-proportioned.

 In shell hardening process,we use aluminium chloride to harden the shell.This can make the shell so hard that it can`t be distorted,at the same time the bug which the casting may have will be decreased.If there are letters or numbers in it,they will be much clearer.

 In dewaxing process,about 95% of the castings suppliers adopt the original water dewaxing technics,but we using the advanced steam dewaxing technics,which we are very proud of. This can effectively avoid the air-hole and sand-hole, making the casting look much nicer.

 In smelt process, we use middle frequency furnace, avoiding the emergence of the oxide; in molten steel control part, we use Germany-imported direct reading spectrometer machine, assuring its quality before the molten steel out of the furnace. During this process we use ERP production and management software to get the feedback information.

 In shell-knock out process, we have special machines,which can decrease the hitting and knocking, easily made by manual shell knocking out.

 In shot-blasting process, we have crawler-type and hanging shot-blasting machine, with steel shot 0.5-0.8, making the products smooth.Of course, if the customer wants it look much nicer, we also can carry out sand-blast treatment.

 In heat treatment process, we use electric furnace, and adopt double-temperature control in order to heat the products equally. As a result, the products will have great metallurgical structure.

 Our tolerance can reach at the grade of 5-7 according to our country`s tolerance standard.

 In machining process,we have 12 CNC machining centers and some other machines, so we can make further machining if the customers need.

Architectural Hardware Precision Casting

Architectural Hardware Precision Casting,Architectural Hardware Lost Wax Casts,Architectural Hardware Investment Casting,Investment Casting for Architectural Hardware

Wei fang junlong precision casting Co.,Ltd , http://www.junlongcasting.com